krupek

Racja WalDo, to są moje niewłaściwe przyzwyczajenia dlatego na to iso trzeba przymrużyć oko. Hihi Pozdr.

Trafna uwaga sokar620 kolega chce normalna kopie systemu. Podejrzewam że zainteresuje Cię bardzo bezpiecznie polecenie „dd” do zrealizowania zamierzonego celu. Przykładowo: /dev/sda1 – boot /dev/sba2 – swap /dev/sda3 - / odpalasz system z płytki: linux rescue i tam dajesz następujące polecenie: dd if=/dev/sda3 of=/obraz.iso obraz.iso możesz sobie wypalić albo skopiować gdzie tam... pamiętaj ze jest tam tylko jedna partycja „sda3” jak juz przyjdzie czas na odtworzenie ponownie uruchamiasz system z płytki linux rescue dd if=/obraz.iso of=/dev/sda3 mozna tez zrobic obraz całego dysku dd if=/dev/sda of=wielkiobraz.iso wada tego rozwiazania jet to ze wielkosc pliku obraz bedzie tak wielki jak partycja bądź caly dysk

A jeszcze ja cos dodam: resize2fs -p /dev/grupa/volumin lub resize2fs -p /dev/sda9 rozciągnie system plików do maksymalnej wielkości bez podawania wartości naj lepiej na systemie zamontowanym tylko do odczytu albo całkiem o ile to możliwe.

Serdecznie witam Moja fizyczna maszyna posiada dwa interfejsy sieciowe eth0 i eth1 (IBM x3650). Jest tam zainstalowany cent z wirtualizacją oraz kilka maszyn wirtualnych. Każda z nich działa posiada jeden interfejs eth0 (i ocz lo). Maże o tym aby do jednej z tych maszyn zamapować interfejs z fizycznej maszyny np. eth1 z IBM-a. Ostatecznie na jednej dom-u chce mieć dwa interfejsy jeden bezpośrednio na fizyczną kartę a drugi standardowo w bridg-u. Standardowo mam tak: vif = [ "mac=00:16:3e:5a:d6:7e,bridge=xenbr0" ]

add1) smartctl -a /dev/sda smartctl version 5.36 [i686-redhat-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ Device: EMC SYMMETRIX Version: 5568 Serial number: 500371068031 Device type: disk Local Time is: Fri Dec 19 10:41:15 2008 CET Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors write: 0 0 0 0 0 0.000 0 Device does not support Self Test logging Niestety niewiele tego jest. Ale właśnie przyszło mi do głowy że może to być problem sterownika bo nie zła jatka była podczas instalacji. Sterownik zainstalował się tylko na „normalnym” jądrze 2.6.18-53.el5 (musiałem nawet ram wyciągać podczas instalacji żeby nie było PAE, a i na RH 5.2 już nie działał). Jak już się zainstalowała karta FC dopiero doinstalowywałem jajo z xen-em. Uaktualnienie jaja nie wchodzi w grę bo nie będzie działał sterownik. Jak ma ktoś jeszcze jakiś pomysł jak to jeszcze uratować to ...

Witam o 9:50 da DOM-0 do nowo podmontowanego LVM kopiowalem plik (dd if=/dev/zero of=/mnt/plik) logi z dom-0 xend.log [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/2/5632/hotplug-status. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices irq. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices vkbd. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices vfb. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices pci. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices ioports. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices tap. [2008-12-11 08:07:08 xend 3467] DEBUG (DevController:143) Waiting for devices vtpm. [2008-12-11 08:07:08 xend 3467] INFO (XendDomain:380) Domain POSTGRES_1 (2) unpaused. [2008-12-18 10:01:24 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:989) XendDomainInfo.handleShutdownWatch [2008-12-18 10:01:24 xend.XendDomainInfo 3467] INFO (XendDomainInfo:1025) HVM save:remote shutdown dom 2! [2008-12-18 10:01:47 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:1560) XendDomainInfo.destroy: domid=2 [2008-12-18 10:01:47 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:1568) XendDomainInfo.destroyDomain(2) [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:200) XendDomainInfo.create(['vm', ['name', 'POSTGRES_1'], ['memory', 512], ['maxmem', 1024], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['vcpus', 1], ['uuid', 'af73a3d0-052c-8c87-92eb-d8b55f8f8589'], ['image', ['hvm', ['kernel', '/usr/lib/xen/boot/hvmloader'], ['device_model', '/usr/lib/xen/bin/qemu-dm'], ['pae', 1], ['vcpus', 1], ['boot', 'c'], ['serial', 'pty'], ['vnc', 1], ['vncunused', 1], ['xauthority', '/root/.Xauthority'], ['acpi', 1], ['apic', 1]]], ['device', ['vbd', ['uname', 'phy:/dev/grupavol/Vol2'], ['dev', 'hda'], ['mode', 'w']]], ['device', ['vbd', ['uname', ''], ['dev', 'hdc:cdrom'], ['mode', 'r']]], ['device', ['vif', ['bridge', 'xenbr0'], ['mac', '00:16:3e:0a:5e:61']]]]) [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:306) parseConfig: config is ['vm', ['name', 'POSTGRES_1'], ['memory', 512], ['maxmem', 1024], ['on_poweroff', 'destroy'], ['on_reboot', 'restart'], ['on_crash', 'restart'], ['vcpus', 1], ['uuid', 'af73a3d0-052c-8c87-92eb-d8b55f8f8589'], ['image', ['hvm', ['kernel', '/usr/lib/xen/boot/hvmloader'], ['device_model', '/usr/lib/xen/bin/qemu-dm'], ['pae', 1], ['vcpus', 1], ['boot', 'c'], ['serial', 'pty'], ['vnc', 1], ['vncunused', 1], ['xauthority', '/root/.Xauthority'], ['acpi', 1], ['apic', 1]]], ['device', ['vbd', ['uname', 'phy:/dev/grupavol/Vol2'], ['dev', 'hda'], ['mode', 'w']]], ['device', ['vbd', ['uname', ''], ['dev', 'hdc:cdrom'], ['mode', 'r']]], ['device', ['vif', ['bridge', 'xenbr0'], ['mac', '00:16:3e:0a:5e:61']]]] [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:411) parseConfig: result is {'shadow_memory': None, 'start_time': None, 'uuid': 'af73a3d0-052c-8c87-92eb-d8b55f8f8589', 'on_crash': 'restart', 'on_reboot': 'restart', 'localtime': None, 'image': ['hvm', ['kernel', '/usr/lib/xen/boot/hvmloader'], ['device_model', '/usr/lib/xen/bin/qemu-dm'], ['pae', 1], ['vcpus', 1], ['boot', 'c'], ['serial', 'pty'], ['vnc', 1], ['vncunused', 1], ['xauthority', '/root/.Xauthority'], ['acpi', 1], ['apic', 1]], 'on_poweroff': 'destroy', 'bootloader_args': None, 'cpus': None, 'name': 'POSTGRES_1', 'backend': [], 'vcpus': 1, 'cpu_weight': None, 'features': None, 'vcpu_avail': None, 'memory': 512, 'device': [('vbd', ['vbd', ['uname', 'phy:/dev/grupavol/Vol2'], ['dev', 'hda'], ['mode', 'w']]), ('vbd', ['vbd', ['uname', ''], ['dev', 'hdc:cdrom'], ['mode', 'r']]), ('vif', ['vif', ['bridge', 'xenbr0'], ['mac', '00:16:3e:0a:5e:61']])], 'bootloader': None, 'cpu': None, 'maxmem': 1024} [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:1350) XendDomainInfo.construct: None [2008-12-18 10:01:56 xend 3467] DEBUG (balloon:127) Balloon: 543636 KiB free; need 2048; done. [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:1398) XendDomainInfo.initDomain: 3 1.0 [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: boot, val: c [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: fda, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: fdb, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: soundhw, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: localtime, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: serial, val: pty [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: std-vga, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: isa, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: vcpus, val: 1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: acpi, val: 1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: usb, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: usbdevice, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:324) args: k, val: None [2008-12-18 10:01:56 xend 3467] DEBUG (image:384) No VNC passwd configured for vfb access [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:1437) _initDomain:shadow_memory=0x0, maxmem=0x400, memory=0x200. [2008-12-18 10:01:56 xend 3467] DEBUG (balloon:127) Balloon: 542608 KiB free; need 541696; done. [2008-12-18 10:01:56 xend 3467] INFO (image:137) buildDomain os=None dom=3 vcpus=1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:269) domid = 3 [2008-12-18 10:01:56 xend 3467] DEBUG (image:270) image = /usr/lib/xen/boot/hvmloader [2008-12-18 10:01:56 xend 3467] DEBUG (image:271) store_evtchn = 2 [2008-12-18 10:01:56 xend 3467] DEBUG (image:272) memsize = 512 [2008-12-18 10:01:56 xend 3467] DEBUG (image:273) vcpus = 1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:274) pae = 1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:275) acpi = 1 [2008-12-18 10:01:56 xend 3467] DEBUG (image:276) apic = 1 [2008-12-18 10:01:56 xend 3467] DEBUG (blkif:24) exception looking up device number for hda: [Errno 2] No such file or directory: '/dev/hda' [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'virtual-device': '768', 'device-type': 'disk', 'state': '1', 'backend': '/local/domain/0/backend/vbd/3/768'} to /local/domain/3/device/vbd/768. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:112) DevController: writing {'domain': 'POSTGRES_1', 'frontend': '/local/domain/3/device/vbd/768', 'format': 'raw', 'dev': 'hda', 'state': '1', 'params': '/dev/grupavol/Vol2', 'mode': 'w', 'online': '1', 'frontend-id': '3', 'type': 'phy'} to /local/domain/0/backend/vbd/3/768. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'virtual-device': '5632', 'device-type': 'cdrom', 'state': '1', 'backend': '/local/domain/0/backend/vbd/3/5632'} to /local/domain/3/device/vbd/5632. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:112) DevController: writing {'domain': 'POSTGRES_1', 'frontend': '/local/domain/3/device/vbd/5632', 'format': 'raw', 'dev': 'hdc', 'state': '1', 'params': '', 'mode': 'r', 'online': '1', 'frontend-id': '3', 'type': ''} to /local/domain/0/backend/vbd/3/5632. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'mac': '00:16:3e:0a:5e:61', 'handle': '0', 'state': '1', 'backend': '/local/domain/0/backend/vif/3/0'} to /local/domain/3/device/vif/0. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:112) DevController: writing {'bridge': 'xenbr0', 'domain': 'POSTGRES_1', 'handle': '0', 'script': '/etc/xen/scripts/vif-bridge', 'state': '1', 'frontend': '/local/domain/3/device/vif/0', 'mac': '00:16:3e:0a:5e:61', 'online': '1', 'frontend-id': '3'} to /local/domain/0/backend/vif/3/0. [2008-12-18 10:01:56 xend 3467] INFO (image:428) spawning device models: /usr/lib/xen/bin/qemu-dm ['/usr/lib/xen/bin/qemu-dm', '-d', '3', '-m', '512', '-boot', 'c', '-serial', 'pty', '-vcpus', '1', '-acpi', '-domain-name', 'POSTGRES_1', '-net', 'nic,vlan=1,macaddr=00:16:3e:0a:5e:61,model=rtl8139', '-net', 'tap,vlan=1,bridge=xenbr0', '-vnc', '127.0.0.1:3', '-vncunused'] [2008-12-18 10:01:56 xend 3467] INFO (image:430) device model pid: 31706 [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:756) Storing VM details: {'shadow_memory': '9', 'uuid': 'af73a3d0-052c-8c87-92eb-d8b55f8f8589', 'on_reboot': 'restart', 'start_time': '1229590916.54', 'on_poweroff': 'destroy', 'name': 'POSTGRES_1', 'xend/restart_count': '0', 'vcpus': '1', 'vcpu_avail': '1', 'memory': '512', 'on_crash': 'restart', 'image': '(hvm (kernel /usr/lib/xen/boot/hvmloader) (device_model /usr/lib/xen/bin/qemu-dm) (pae 1) (vcpus 1) (boot c) (serial pty) (vnc 1) (vncunused 1) (xauthority /root/.Xauthority) (acpi 1) (apic 1))', 'maxmem': '1024'} [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:791) Storing domain details: {'console/port': '3', 'name': 'POSTGRES_1', 'console/limit': '1048576', 'vm': '/vm/af73a3d0-052c-8c87-92eb-d8b55f8f8589', 'domid': '3', 'cpu/0/availability': 'online', 'memory/target': '524288', 'store/ring-ref': '131070', 'store/port': '2'} [2008-12-18 10:01:56 xend.XendDomainInfo 3467] DEBUG (XendDomainInfo:989) XendDomainInfo.handleShutdownWatch [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices vif. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:149) Waiting for 0. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vif/3/0/hotplug-status. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vif/3/0/hotplug-status. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices usb. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices vbd. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:149) Waiting for 768. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/3/768/hotplug-status. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/3/768/hotplug-status. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:149) Waiting for 5632. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/3/5632/hotplug-status. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices irq. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices vkbd. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices vfb. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices pci. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices ioports. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices tap. [2008-12-18 10:01:56 xend 3467] DEBUG (DevController:143) Waiting for devices vtpm. [2008-12-18 10:01:56 xend 3467] INFO (XendDomain:380) Domain POSTGRES_1 (3) unpaused. dmesg Linux version 2.6.18-92.1.13.el5xen ([email protected]) (gcc version 4.1.2 20071124 (Red Hat 4.1.2-42)) #1 SMP We d Sep 24 20:44:26 EDT 2008 BIOS-provided physical RAM map: Xen: 0000000000000000 - 00000000f57cb000 (usable) 3199MB HIGHMEM available. 727MB LOWMEM available. Using x86 segment limits to approximate NX protection On node 0 totalpages: 1005515 DMA zone: 186366 pages, LIFO batch:31 HighMem zone: 819149 pages, LIFO batch:31 DMI 2.4 present. ACPI: RSDP (v002 IBM ) @ 0x000fdfd0 ACPI: XSDT (v001 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce9c0 ACPI: FADT (v002 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce900 ACPI: MADT (v001 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce840 ACPI: SRAT (v001 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce700 ACPI: HPET (v001 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce6c0 ACPI: MCFG (v001 IBM SERVALNT 0x00001000 IBM 0x45444f43) @ 0xbffce680 ACPI: DSDT (v002 IBM SERVALNT 0x00001000 INTL 0x20041203) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 14, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Built 1 zonelists. Total pages: 1005515 Kernel command line: ro root=/dev/sda2 rhgb quiet Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c073c000 soft=c071c000 PID hash table entries: 4096 (order: 12, 16384 bytes) Xen reported: 2327.552 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB enabled: Aperture: 64 megabytes Kernel range: 0x00000000c34c2000 - 0x00000000c74c2000 vmalloc area: ee000000-f4ffe000, maxmem 2d7fe000 Memory: 3898300k/4022060k available (2099k kernel code, 114348k reserved, 870k data, 176k init, 3276596k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5821.19 BogoMIPS (lpj=11642396) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebd3f1 20000000 00000000 00000000 0004e3bd 00000000 00000001 CPU: After vendor identify, caps: bfebd3f1 20000000 00000000 00000000 0004e3bd 00000000 00000001 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: After all inits, caps: bfebd3f1 20000000 00000000 00000940 0004e3bd 00000000 00000001 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU 1 irqstacks, hard=c073d000 soft=c071d000 CPU 2 irqstacks, hard=c073e000 soft=c071e000 CPU 3 irqstacks, hard=c073f000 soft=c071f000 ENABLING IO-APIC IRQs SMP alternatives: switching to SMP code Initializing CPU#1 Initializing CPU#2 Brought up 4 CPUs sizeof(vma)=88 bytes sizeof(page)=32 bytes Initializing CPU#3 sizeof(inode)=340 bytes sizeof(dentry)=136 bytes sizeof(ext3inode)=492 bytes sizeof(buffer_head)=52 bytes sizeof(skbuff)=172 bytes migration_cost=11 checking if image is initramfs... it is Freeing initrd memory: 6607k freed Grant table initialized NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 Setting up standard PCI resources Allocating PCI resources starting at c2000000 (gap: c0000000:20000000) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 Boot video device is 0000:01:06.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4.PCI5.PCI6._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4.PCI5.PCI7._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIS._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC2B._PRT] ACPI: PCI Interrupt Link [LP00] (IRQs *3) ACPI: PCI Interrupt Link [LP01] (IRQs *10) ACPI: PCI Interrupt Link [LP02] (IRQs *11) ACPI: Blank IRQ resource ACPI: Resource is not an IRQ entry ACPI: PCI Interrupt Link [LP03] (IRQs) *0, disabled. ACPI: PCI Interrupt Link [LP04] (IRQs *3) ACPI: Blank IRQ resource ACPI: Resource is not an IRQ entry ACPI: PCI Interrupt Link [LP05] (IRQs) *0, disabled. ACPI: PCI Interrupt Link [LP06] (IRQs *11) ACPI: PCI Interrupt Link [LP07] (IRQs *5) Linux Plug and Play Support v0.97 © Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices xen_mem: Initialising balloon driver. usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:01: ioport range 0x520-0x53f has been reserved pnp: 00:01: ioport range 0x540-0x547 has been reserved pnp: 00:08: ioport range 0xca8-0xca8 has been reserved pnp: 00:08: ioport range 0xcac-0xcac has been reserved pnp: 00:09: ioport range 0x400-0x43f has been reserved PCI: Bridge: 0000:1b:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:1b:01.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:1a:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:1a:00.3 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:03.0 IO window: 5000-5fff MEM window: c8000000-c9ffffff PREFETCH window: c7f00000-c7ffffff PCI: Bridge: 0000:00:04.0 IO window: 7000-ffff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: 6000-6fff MEM window: c6000000-c7efffff PREFETCH window: c2000000-c20fffff PCI: Bridge: 0000:00:07.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: cd000000-cfffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: cd000000-cfffffff PREFETCH window: disabled. PCI: Bridge: 0000:05:00.0 IO window: disabled. MEM window: ca000000-ccffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: ca000000-ccffffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: 3000-4fff MEM window: de000000-dfffffff PREFETCH window: d0000000-ddffffff PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:1a:00.0 to 64 PCI: Setting latency timer of device 0000:1b:00.0 to 64 ACPI: PCI Interrupt 0000:1b:01.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:1b:01.0 to 64 PCI: Setting latency timer of device 0000:1a:00.3 to 64 PCI: Setting latency timer of device 0000:00:03.0 to 64 PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:07.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 21 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.0 to 64 PCI: Setting latency timer of device 0000:02:00.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[b] -> GSI 20 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.1 to 64 PCI: Setting latency timer of device 0000:05:00.0 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1228979069.952:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 20B65DCA289A0EEF - User ID: CentOS (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] PCI: Setting latency timer of device 0000:00:03.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:03.0:pcie00] PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] PCI: Setting latency timer of device 0000:00:07.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:07.0:pcie00] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] PCI: Setting latency timer of device 0000:1a:00.0 to 64 Allocate Port Service[0000:1a:00.0:pcie10] PCI: Setting latency timer of device 0000:1b:00.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:1b:00.0:pcie20] PCI: Setting latency timer of device 0000:1b:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:1b:01.0:pcie20] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Processor [CPU2] (supports 8 throttling states) ACPI: Processor [CPU3] (supports 8 throttling states) Real Time Clock Driver v1.12ac hpet_acpi_add: no address or irqs in _CRS Non-volatile memory driver v1.2 Linux agpgart interface v0.101 © Dave Jones RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize Xen virtual console successfully installed as ttyS0 Event-channel device installed. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe Probing IDE interface ide1... hdc: HL-DT-STCD-RW/DVD DRIVE GCC-T10N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Freeing unused kernel memory: 176k freed Write protecting the kernel read-only data: 379k SCSI subsystem initialized QLogic Fibre Channel HBA Driver: 8.02.14.01 ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 18 (level, low) -> IRQ 19 qla2xxx 0000:07:00.0: Found an ISP2432, irq 19, iobase 0xee016000 qla2xxx 0000:07:00.0: Configuring PCI space... PCI: Setting latency timer of device 0000:07:00.0 to 64 qla2xxx 0000:07:00.0: Configure NVRAM parameters... qla2xxx 0000:07:00.0: Found mismatch in adapter port names. qla2xxx 0000:07:00.0: qla0 port name found in NVRAM -> 2100001b321ada0b qla2xxx 0000:07:00.0: qla0 port name found on command line -> 2100001b321ad60a qla2xxx 0000:07:00.0: Using port name from NVRAM. qla2xxx 0000:07:00.0: Verifying loaded RISC code... qla2xxx 0000:07:00.0: Allocated (64 KB) for EFT... qla2xxx 0000:07:00.0: Allocated (1413 KB) for firmware dump... qla2xxx 0000:07:00.0: Waiting for LIP to complete... qla2xxx 0000:07:00.0: LIP reset occured (f7f7). qla2xxx 0000:07:00.0: LOOP UP detected (1 Gbps). qla2xxx 0000:07:00.0: Topology - (F_Port), Host Loop address 0x0 scsi0 : qla2xxx qla2xxx 0000:07:00.0: QLogic Fibre Channel HBA Driver: 8.02.14.01 QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel ISP2432: PCIe (2.5GT/s x4) @ 0000:07:00.0 hdma+, host#=0, fw=4.04.00 [iP] [84XX] Vendor: EMC Model: SYMMETRIX Rev: 5568 Type: Direct-Access ANSI SCSI revision: 02 qla2xxx 0000:07:00.0: scsi(0:0:1:0): Enabled tagged queuing, queue depth 32. SCSI device sda: 1060147200 512-byte hdwr sectors (542795 MB) sda: Write Protect is off sda: Mode Sense: 83 00 00 08 SCSI device sda: drive cache: write through SCSI device sda: 1060147200 512-byte hdwr sectors (542795 MB) sda: Write Protect is off sda: Mode Sense: 83 00 00 08 SCSI device sda: drive cache: write through sda: sda1 sda2 sda3 sda4 sd 0:0:1:0: Attached scsi disk sda USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002200 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 21, io base 0x00002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 20, io base 0x00002a00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 21, io base 0x00002e00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 1-1: new low speed USB device using uhci_hcd and address 2 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf9000000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected Adaptec aacraid driver 1.1-5[2453] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:04:00.0 to 64 AAC0: kernel 5.2-0[15411] Oct 11 2007 AAC0: monitor 5.2-0[15411] AAC0: bios 5.2-0[15411] AAC0: serial 403C689 AAC0: 64bit support enabled. AAC0: 64 Bit DAC enabled scsi1 : ServeRAID usb 1-1: device not accepting address 2, error -71 usb 1-1: new low speed USB device using uhci_hcd and address 4 Vendor: IBM-ESXS Model: VSC7160 Rev: 1.07 Type: Enclosure ANSI SCSI revision: 03 usb 1-1: configuration #1 chosen from 1 choice input: ATEN UC-10KM V1.3.121 as /class/input/input0 input: USB HID v1.10 Keyboard [ATEN UC-10KM V1.3.121] on usb-0000:00:1d.0-1 input: ATEN UC-10KM V1.3.121 as /class/input/input1 input: USB HID v1.10 Mouse [ATEN UC-10KM V1.3.121] on usb-0000:00:1d.0-1 usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice input: IBM IBM RSA2 as /class/input/input2 input: USB HID v1.10 Keyboard [iBM IBM RSA2] on usb-0000:00:1d.2-1 input: IBM IBM RSA2 as /class/input/input3 input: USB HID v1.10 Mouse [iBM IBM RSA2] on usb-0000:00:1d.2-1 hiddev96: USB HID v1.10 Device [iBM IBM RSA2] on usb-0000:00:1d.2-1 libata version 3.00 loaded. ata_piix 0000:00:1f.2: version 2.12 ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 20 (level, low) -> IRQ 18 ata_piix 0000:00:1f.2: 0x170 IDE port busy PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi2 : ata_piix scsi3 : ata_piix ata1: SATA max UDMA/133 bmdma 0x480 irq 14 ata2: DUMMY EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. security: 3 users, 6 roles, 1658 types, 210 bools, 1 sens, 1024 cats security: 61 classes, 57675 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev sda2, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), not configured for labeling SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1228979087.757:2): policy loaded auid=4294967295 ses=4294967295 EDAC MC: Ver: 2.0.1 Sep 24 2008 EDAC MC0: Giving out device to i5000_edac.c I5000: DEV 0000:00:10.0 ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 20 (level, low) -> IRQ 18 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 8250_pnp: Unknown symbol serial8250_unregister_port 8250_pnp: Unknown symbol serial8250_register_port intel_rng: FWH not detected input: PC Speaker as /class/input/input4 Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.6.9 (December 8, 2007) ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 22 sd 0:0:1:0: Attached scsi generic sg0 type 0 scsi 1:3:0:0: Attached scsi generic sg1 type 13 eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem ce000000, IRQ 22, node addr 001a646acf3d ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level, low) -> IRQ 16 eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem ca000000, IRQ 16, node addr 001a646acf3f floppy0: no floppy controllers found lp: driver loaded but no devices found audit(1228979096.809:3): avc: denied { search } for pid=1698 comm="rhgb" name="/" dev=sda2 ino=2 scontext=system_u:system_r :rhgb_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts audit(1228979097.685:4): avc: denied { getattr } for pid=1700 comm="sh" path="/" dev=sda2 ino=2 scontext=system_u:system_r: rhgb_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir audit(1228979097.689:5): avc: denied { search } for pid=1700 comm="ifconfig" name="/" dev=sda2 ino=2 scontext=system_u:syst em_r:ifconfig_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir audit(1228979097.693:6): avc: denied { read } for pid=1702 comm="setfont" name="/" dev=sda2 ino=2 scontext=system_u:system_ r:rhgb_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir audit(1228979098.053:7): avc: denied { search } for pid=1699 comm="rhgb" name="/" dev=sda2 ino=2 scontext=system_u:system_r :rhgb_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir ACPI: Power Button (FF) [PWRF] ibm_acpi: ec object not found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: [email protected] device-mapper: multipath: version 1.0.5 loaded loop: loaded (max 8 devices) EXT3 FS on sda2, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda1, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs kjournald starting. Commit interval 5 seconds EXT3 FS on dm-3, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev dm-3, type ext3), uses xattr Adding 4096564k swap on /dev/sda3. Priority:-1 extents:1 across:4096564k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts IA-32 Microcode Update Driver: v1.14-xen <[email protected]> audit(1228979122.827:8): avc: denied { search } for pid=2137 comm="microcode_ctl" name="/" dev=sda2 ino=2 scontext=system_u :system_r:cpucontrol_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir audit(1228979123.803:9): avc: denied { search } for pid=2206 comm="iptables-restor" name="/" dev=sda2 ino=2 scontext=system _u:system_r:iptables_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir ip_tables: © 2000-2006 Netfilter Core Team audit(1228979124.119:10): avc: denied { search } for pid=2206 comm="iptables-restor" name="/" dev=sda2 ino=2 scontext=syste m_u:system_r:iptables_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 228 bytes per conntrack audit(1228979125.103:11): avc: denied { search } for pid=2309 comm="ip" name="/" dev=sda2 ino=2 scontext=system_u:system_r: ifconfig_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir audit(1228979125.271:12): avc: denied { search } for pid=2319 comm="arping" name="/" dev=sda2 ino=2 scontext=system_u:syste m_r:netutils_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir bnx2: eth0 NIC Copper Link is Up, 100 Mbps full duplex audit(1228979129.887:13): avc: denied { search } for pid=2446 comm="auditd" name="/" dev=sda2 ino=2 scontext=system_u:syste m_r:auditd_t:s0 tcontext=system_u:object_r:file_t:s0 tclass=dir SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.1 SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts Bridge firewalling registered virbr0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. xenbr0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature. device vif0.0 entered promiscuous mode xenbr0: topology change detected, propagating xenbr0: port 1(vif0.0) entering forwarding state bnx2: peth0 NIC Copper Link is Up, 100 Mbps full duplex device peth0 entered promiscuous mode xenbr0: topology change detected, propagating xenbr0: port 2(peth0) entering forwarding state tun: Universal TUN/TAP device driver, 1.6 tun: © 1999-2004 Max Krasnyansky <[email protected]> device tap0 entered promiscuous mode xenbr0: topology change detected, propagating xenbr0: port 3(tap0) entering forwarding state device vif1.0 entered promiscuous mode device tap1 entered promiscuous mode xenbr0: topology change detected, propagating xenbr0: port 5(tap1) entering forwarding state device vif2.0 entered promiscuous mode messages Dec 14 04:02:02 localhost syslogd 1.4.1: restart. Dec 15 15:18:12 localhost restorecond: Will not restore a file with more than one hard link (/etc/resolv.conf) No such file or directory Dec 17 12:02:28 localhost restorecond: Will not restore a file with more than one hard link (/etc/resolv.conf) No such file or directory Dec 18 09:12:51 localhost kernel: kjournald starting. Commit interval 5 seconds Dec 18 09:12:51 localhost kernel: EXT3 FS on dm-4, internal journal Dec 18 09:12:51 localhost kernel: EXT3-fs: mounted filesystem with ordered data mode. Dec 18 10:00:10 localhost kernel: xenbr0: port 5(tap1) entering disabled state Dec 18 10:00:10 localhost kernel: device tap1 left promiscuous mode Dec 18 10:00:10 localhost kernel: xenbr0: port 5(tap1) entering disabled state Dec 18 10:01:48 localhost kernel: xenbr0: port 6(vif2.0) entering disabled state Dec 18 10:01:48 localhost kernel: device vif2.0 left promiscuous mode Dec 18 10:01:48 localhost kernel: xenbr0: port 6(vif2.0) entering disabled state Dec 18 10:01:56 localhost kernel: device tap1 entered promiscuous mode Dec 18 10:01:56 localhost kernel: xenbr0: topology change detected, propagating Dec 18 10:01:56 localhost kernel: xenbr0: port 5(tap1) entering forwarding state Dec 18 10:01:56 localhost kernel: device vif3.0 entered promiscuous mode <><>><>><><><><><>><><><><><><><><><><><><><><><><><><><><><> dom-u messages Dec 14 04:02:07 POSTGRES-1 syslogd 1.4.1: restart. Dec 18 09:11:25 POSTGRES-1 kernel: Kernel logging (proc) stopped. Dec 18 09:11:25 POSTGRES-1 kernel: Kernel log daemon terminating. Dec 18 09:11:26 POSTGRES-1 exiting on signal 15 Dec 18 09:11:26 POSTGRES-1 syslogd 1.4.1: restart. Dec 18 09:11:26 POSTGRES-1 kernel: klogd 1.4.1, log source = /proc/kmsg started. Dec 18 09:50:47 POSTGRES-1 kernel: hda: dma_timer_expiry: dma status == 0x21 Dec 18 09:50:57 POSTGRES-1 kernel: hda: DMA timeout error Dom-0 posiada karte qlogic2460 sterowniki ze stronki qlogic system wykrywa jako sda nie ma dysków lokalnych wszystko jest na macierzy IBM x3650 na intelu

Problem polega na tym ze mam na Dom-0 są jakieś tam wirtualne maszyny prawidłowo działające. Wpadłem na pomysł doinstalować jeszcze jedną stworzyłem sobie kolejnego lvm-a gdzie przydzieliłem nowy virt.-system. Podczas instalacji a konkretnie kopiowania paczek na dysk, dwie wcześniej poprawnie działające maszyny się zawiesiły. Odkryłem że ta sytuacja mam miejsce nie tylko podczas instalacji ale tak że, wtedy jak kopiuje coś ma DOM-0 np. (np. film). Nie ma znaczenia czy systemy jest na lvm czy w pliku. Taki sam problem mam na 2 fizycznych serwerach obydwa są podpięte do macierzy przez kartę FC. POMOCY

Warto dać yum clean all to często pomaga

Ale nie mam czegoś takiego w Dom-U nawet nie znalazłem niczego podobnego Natomiast jest na Dom-0 Pozdr.

Do przeglądarki ?? Jaki system i napisz coś więcej...

Zobacz tu

Sorki ze dopiero teraz straszny miałem nawal roboty co nie rozwiązało problemu: /etc/xen/skrzynka_podawcza name = "skrzynka_podawcza" uuid = "e1fc8a2f-a48a-50b5-e8b5-136375cec790" maxmem = 1024 memory = 1024 vcpus = 1 bootloader = "/usr/bin/pygrub" on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ "type=vnc,vncunused=1" ] disk = [ "tap:aio:/var/lib/xen/images/skrzynka_podawcza.img,xvda,w","file:/os/CentOS-5.1-i386-bin-DVD.iso,hdc:cdrom,r" ] vif = [ "mac=00:16:3e:2f:71:f2,bridge=xenbr0" ] nie mam hda mam fdisk -l /dev/xvda z dom-U Disk /dev/xvda: 64.4 GB, 64424509440 bytes 255 heads, 63 sectors/track, 7832 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/xvda1 * 1 13 104391 83 Linux /dev/xvda2 14 274 2096482+ 82 Linux swap / Solaris /dev/xvda3 275 7832 60709635 83 Linux oraz cat /etc/fstab LABEL=/ / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 LABEL=SWAP-xvda2 swap swap defaults 0 0

Witam zgłaszam się z problemem czasu. Po wykonaniu polecenia na wirtualnym systemie (Dom-U): for ((i=0; i<20; i++)) do date; done; efekt jest poniżej po restarcie jeden dzień jest ok a po jakimś czasie z powrotem się rozjeżdża(1 dzień). czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 czw lis 6 08:47:46 CET 2008 czw lis 6 10:01:04 CET 2008 Czy wiecie gdzie może być przyczyna i jak to poprawić.

Witam ponownie Dalej to nie jest tak jak bym oczekiwał. Oto efekt kolejnego testu: Na potrzeby testu stworzyłem 5 lvm 100,200,300,400 i 500 Mega ich kolejne nazwy to test1-5 w pliku świadomie zrobiłem 2 targety z 3 i 2 'lun-ami' /etc/ietd.conf Target iqn.2008-08.host1:storage.volume1.ISCSI1 Lun 0 Path=/dev/volgru00/test1,Type=fileio Lun 1 Path=/dev/volgru00/test2,Type=blockio Lun 2 Path=/dev/volgru00/test3,Type=blockio Alias ISCSI1.host1 Target iqn.2008-09.host4:storage.volume4.ISCSI4 Lun 0 Path=/dev/volgru00/test4,Type=blockio Lun 1 Path=/dev/volgru00/test5,Type=blockio Alias ISCSI1.host2 A teraz najciekawsze efekt polecenia (hda to mój lokalny dysk - wiadomo) fdisk -l Disk /dev/hda: 10.2 GB, 10248118272 bytes 255 heads, 63 sectors/track, 1245 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 * 1 13 104391 83 Linux /dev/hda2 14 1033 8193150 83 Linux /dev/hda3 1034 1164 1052257+ 82 Linux swap / Solaris /dev/hda4 1165 1245 650632+ 8e Linux LVM Disk /dev/sda: 104 MB, 104857600 bytes 4 heads, 50 sectors/track, 1024 cylinders Units = cylinders of 200 * 512 = 102400 bytes Device Boot Start End Blocks Id System Disk /dev/sdb: 419 MB, 419430400 bytes 13 heads, 62 sectors/track, 1016 cylinders Units = cylinders of 806 * 512 = 412672 bytes Disk /dev/sdb doesn't contain a valid partition table Disk /dev/sdc: 209 MB, 209715200 bytes 7 heads, 58 sectors/track, 1008 cylinders Units = cylinders of 406 * 512 = 207872 bytes Device Boot Start End Blocks Id System Disk /dev/sdd: 524 MB, 524288000 bytes 17 heads, 59 sectors/track, 1020 cylinders Units = cylinders of 1003 * 512 = 513536 bytes Device Boot Start End Blocks Id System Disk /dev/sde: 314 MB, 314572800 bytes 10 heads, 60 sectors/track, 1024 cylinders Units = cylinders of 600 * 512 = 307200 bytes Device Boot Start End Blocks Id System przy innych konfiguracjach bywa ze widziane są tylko 3 przestrzenie na sda, sdd i sde – w przypadkowej kolejności(np.dla poszczególnego targetu jeden lun i tak 5 razy). Boje sie że jak dodam następną przestrzeń to całkiem pozmieniają sie ich lokalizacje. Potrzebuje to do osadzenia maszyn wirtualnych więc dokładność ulokowania jest istotna. Zresztą tak czy siak trzeba to jakoś okiełznać. Pozdrawiam zainteresowanych. I dzięki za odpowiedzi.

[2008-10-28 23:37:20 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:411) parseConfig: result is {'shadow_memory': 8, 'start_time': 1225231611.1300001, 'uuid': 'b88e8044-bda1-dac3-6fb3-c5d29b613cb6', 'on_crash': 'restart', 'on_reboot': 'restart', 'localtime': None, 'image': ['hvm', ['kernel', '/usr/lib/xen/boot/hvmloader'], ['device_model', '/usr/lib/xen/bin/qemu-dm'], ['pae', 1], ['vcpus', 2], ['boot', 'c'], ['serial', 'pty'], ['vnc', 1], ['vncunused', 1], ['display', ':1.0'], ['xauthority', '/root/.Xauthority'], ['acpi', 1], ['apic', 1]], 'on_poweroff': 'destroy', 'bootloader_args': None, 'cpus': None, 'name': 'POSTGRES_1', 'backend': [], 'vcpus': 2, 'cpu_weight': 1.0, 'features': '', 'vcpu_avail': 3, 'memory': 768, 'device': [('vif', ['vif', ['backend', 0], ['script', 'vif-bridge'], ['bridge', 'xenbr0'], ['mac', '00:16:3e:19:f6:8e']]), ('vbd', ['vbd', ['backend', 0], ['dev', 'hda:disk'], ['uname', 'phy:/dev/VolGru1/Vol1'], ['mode', 'w']]), ('vbd', ['vbd', ['backend', 0], ['dev', 'hdc:cdrom'], ['mode', 'r']])], 'bootloader': None, 'cpu': None, 'maxmem': 768} [2008-10-28 23:37:20 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:1350) XendDomainInfo.construct: None [2008-10-28 23:37:20 xend 3265] DEBUG (balloon:127) Balloon: 804752 KiB free; need 2048; done. [2008-10-28 23:37:20 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:1398) XendDomainInfo.initDomain: 37 1.0 [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: boot, val: c [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: fda, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: fdb, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: soundhw, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: localtime, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: serial, val: pty [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: std-vga, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: isa, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: vcpus, val: 2 [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: acpi, val: 1 [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: usb, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: usbdevice, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:316) args: k, val: None [2008-10-28 23:37:20 xend 3265] DEBUG (image:376) No VNC passwd configured for vfb access [2008-10-28 23:37:20 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:1437) _initDomain:shadow_memory=0x8, maxmem=0x300, memory=0x300. [2008-10-28 23:37:20 xend 3265] DEBUG (balloon:127) Balloon: 803720 KiB free; need 802816; done. [2008-10-28 23:37:20 xend 3265] INFO (image:137) buildDomain os=None dom=37 vcpus=2 [2008-10-28 23:37:20 xend 3265] DEBUG (image:269) domid = 37 [2008-10-28 23:37:20 xend 3265] DEBUG (image:270) image = /usr/lib/xen/boot/hvmloader [2008-10-28 23:37:20 xend 3265] DEBUG (image:271) store_evtchn = 3 [2008-10-28 23:37:20 xend 3265] DEBUG (image:272) memsize = 768 [2008-10-28 23:37:20 xend 3265] DEBUG (image:273) vcpus = 2 [2008-10-28 23:37:20 xend 3265] DEBUG (image:274) pae = 1 [2008-10-28 23:37:20 xend 3265] DEBUG (image:275) acpi = 1 [2008-10-28 23:37:20 xend 3265] DEBUG (image:276) apic = 1 [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'mac': '00:16:3e:19:f6:8e', 'handle': '0', 'state': '1', 'backend': '/local/domain/0/backend/vif/37/0'} to /local/domain/37/device/vif/0. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:112) DevController: writing {'bridge': 'xenbr0', 'domain': 'POSTGRES_1', 'handle': '0', 'script': '/etc/xen/scripts/vif-bridge', 'state': '1', 'frontend': '/local/domain/37/device/vif/0', 'mac': '00:16:3e:19:f6:8e', 'online': '1', 'frontend-id': '37'} to /local/domain/0/backend/vif/37/0. [2008-10-28 23:37:21 xend 3265] DEBUG (blkif:24) exception looking up device number for hda: [Errno 2] No such file or directory: '/dev/hda' [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'virtual-device': '768', 'device-type': 'disk', 'state': '1', 'backend': '/local/domain/0/backend/vbd/37/768'} to /local/domain/37/device/vbd/768. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:112) DevController: writing {'domain': 'POSTGRES_1', 'frontend': '/local/domain/37/device/vbd/768', 'format': 'raw', 'dev': 'hda', 'state': '1', 'params': '/dev/VolGru1/Vol1', 'mode': 'w', 'online': '1', 'frontend-id': '37', 'type': 'phy'} to /local/domain/0/backend/vbd/37/768. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:110) DevController: writing {'backend-id': '0', 'virtual-device': '5632', 'device-type': 'cdrom', 'state': '1', 'backend': '/local/domain/0/backend/vbd/37/5632'} to /local/domain/37/device/vbd/5632. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:112) DevController: writing {'domain': 'POSTGRES_1', 'frontend': '/local/domain/37/device/vbd/5632', 'format': 'raw', 'dev': 'hdc', 'state': '1', 'params': '', 'mode': 'r', 'online': '1', 'frontend-id': '37', 'type': ''} to /local/domain/0/backend/vbd/37/5632. [2008-10-28 23:37:21 xend 3265] INFO (image:420) spawning device models: /usr/lib/xen/bin/qemu-dm ['/usr/lib/xen/bin/qemu-dm', '-d', '37', '-m', '768', '-boot', 'c', '-serial', 'pty', '-vcpus', '2', '-acpi', '-domain-name', 'POSTGRES_1', '-net', 'nic,vlan=1,macaddr=00:16:3e:19:f6:8e,model=rtl8139', '-net', 'tap,vlan=1,bridge=xenbr0', '-vnc', '127.0.0.1:37', '-vncunused'] [2008-10-28 23:37:21 xend 3265] INFO (image:422) device model pid: 31986 [2008-10-28 23:37:21 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:756) Storing VM details: {'shadow_memory': '8', 'uuid': 'b88e8044-bda1-dac3-6fb3-c5d29b613cb6', 'on_reboot': 'restart', 'start_time': '1225233441.23', 'on_poweroff': 'destroy', 'name': 'POSTGRES_1', 'vcpus': '2', 'vcpu_avail': '3', 'memory': '768', 'on_crash': 'restart', 'image': '(hvm (kernel /usr/lib/xen/boot/hvmloader) (device_model /usr/lib/xen/bin/qemu-dm) (pae 1) (vcpus 2) (boot c) (serial pty) (vnc 1) (vncunused 1) (display :1.0) (xauthority /root/.Xauthority) (acpi 1) (apic 1))', 'maxmem': '768'} [2008-10-28 23:37:21 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:791) Storing domain details: {'console/port': '4', 'name': 'POSTGRES_1', 'console/limit': '1048576', 'vm': '/vm/b88e8044-bda1-dac3-6fb3-c5d29b613cb6', 'domid': '37', 'cpu/0/availability': 'online', 'memory/target': '786432', 'store/ring-ref': '196606', 'cpu/1/availability': 'online', 'store/port': '3'} [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices vif. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:149) Waiting for 0. [2008-10-28 23:37:21 xend.XendDomainInfo 3265] DEBUG (XendDomainInfo:989) XendDomainInfo.handleShutdownWatch [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vif/37/0/hotplug-status. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vif/37/0/hotplug-status. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices usb. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices vbd. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:149) Waiting for 768. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/37/768/hotplug-status. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/37/768/hotplug-status. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:149) Waiting for 5632. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:476) hotplugStatusCallback /local/domain/0/backend/vbd/37/5632/hotplug-status. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:490) hotplugStatusCallback 1. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices irq. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices vkbd. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices vfb. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices pci. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices ioports. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices tap. [2008-10-28 23:37:21 xend 3265] DEBUG (DevController:143) Waiting for devices vtpm. to jest xend.log z Dom-0