Wolno Działający Dysk

[xdarkflame]

Witam

 

Mam następujący problem, po zainstalowaniu Fedory 9 coś mi źle dysk skonfigurowało i chodzi dość wolno:

 

[/b][root@infinity ~]# hdparm -tT /dev/sd?

/dev/sda:
  Timing cached reads:   1728 MB in  2.00 seconds = 864.04 MB/sec
  Timing buffered disk reads:  168 MB in  3.03 seconds =  55.51 MB/sec

/dev/sdb:
  Timing cached reads:   782 MB in  2.00 seconds = 390.95 MB/sec
  Timing buffered disk reads:    6 MB in  3.87 seconds =   1.55 MB/sec

[b]

Oba to dyski SATA 2 , tej samej firmy. Na F7,F8 i F9 updatowanej z F8 , nie było tego problemu dopiero po czystej instalacjisię pojawił.

 

Tak jakby UDMA się wyłączyło, ale myślałem że tego na dyskach sata włączać nie trzeba.

 

Będę wdzięczny za wszelką pomoc.

 

Edit:

Tytuł miał być: Wolno Działający Dysk.

[morsik]

Miałem podobny błąd. Pokaż logi, czyli dmesg. Nie wiem dokładnie o co chodzi, ale z tego co przetłumaczyłem z błędu, to tylko jedno urządzenie może korzystać z UDMA, choć ja jakoś tego nie rozumiem jak to możliwe.

[xdarkflame]

Prosze dmesg:

 

Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.25.3-18.fc9.x86_64 (mockbuild@) (gcc version 4.3.0 20080428 (Red Hat 4.3.0-8) (GCC) ) #1 SMP Tue May 13 04:54:47 EDT 2008
Command line: ro root=UUID=426b48bd-0e69-4ef2-b53f-896642325d92 rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfee0000 (usable)
BIOS-e820: 00000000bfee0000 - 00000000bfee3000 (ACPI NVS)
BIOS-e820: 00000000bfee3000 - 00000000bfef0000 (ACPI data)
BIOS-e820: 00000000bfef0000 - 00000000bff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 00000001b0000000 (usable)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 786144) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 1769472) 2 entries of 3200 used
end_pfn_map = 1769472
DMI 2.4 present.
ACPI: RSDP 000F7090, 0014 (r0 GBT   )
ACPI: RSDT BFEE3000, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: FACP BFEE3040, 0074 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: DSDT BFEE30C0, 6550 (r1 GBT    GBTUACPI     1000 MSFT  3000000)
ACPI: FACS BFEE0000, 0040
ACPI: SSDT BFEE9700, 02CC (r1 PTLTD  POWERNOW        1  LTP        1)
ACPI: HPET BFEE9A00, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU       98)
ACPI: MCFG BFEE9A40, 003C (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: APIC BFEE9640, 0084 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-00000001b0000000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 786144) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 1769472) 2 entries of 3200 used
Bootmem setup node 0 0000000000000000-00000001b0000000
 NODE_DATA [0000000000010000 - 0000000000017fff]
 bootmap [0000000000018000 -  000000000004dfff] pages 36
early res: 0 [0-fff] BIOS data page
early res: 1 [6000-7fff] SMP_TRAMPOLINE
early res: 2 [200000-75db3b] TEXT DATA BSS
early res: 3 [37d1b000-37fef883] RAMDISK
early res: 4 [9f800-a07ff] EBDA
early res: 5 [8000-ffff] PGTABLE
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
[ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
[ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
[ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
[ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
[ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
[ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
[ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
[ffffe20001c00000-ffffe20001dfffff] PMD ->ffff810004a00000 on node 0
[ffffe20001e00000-ffffe20001ffffff] PMD ->ffff810004e00000 on node 0
[ffffe20002000000-ffffe200021fffff] PMD ->ffff810005200000 on node 0
[ffffe20002200000-ffffe200023fffff] PMD ->ffff810005600000 on node 0
[ffffe20002400000-ffffe200025fffff] PMD ->ffff810005a00000 on node 0
[ffffe20002600000-ffffe200027fffff] PMD ->ffff810005e00000 on node 0
[ffffe20002800000-ffffe200029fffff] PMD ->ffff810006200000 on node 0
[ffffe20003800000-ffffe200039fffff] PMD ->ffff810006600000 on node 0
[ffffe20003a00000-ffffe20003bfffff] PMD ->ffff810006a00000 on node 0
[ffffe20003c00000-ffffe20003dfffff] PMD ->ffff810006e00000 on node 0
[ffffe20003e00000-ffffe20003ffffff] PMD ->ffff810007200000 on node 0
[ffffe20004000000-ffffe200041fffff] PMD ->ffff810007600000 on node 0
[ffffe20004200000-ffffe200043fffff] PMD ->ffff810007a00000 on node 0
[ffffe20004400000-ffffe200045fffff] PMD ->ffff810007e00000 on node 0
[ffffe20004600000-ffffe200047fffff] PMD ->ffff810008200000 on node 0
[ffffe20004800000-ffffe200049fffff] PMD ->ffff810008600000 on node 0
[ffffe20004a00000-ffffe20004bfffff] PMD ->ffff810008a00000 on node 0
[ffffe20004c00000-ffffe20004dfffff] PMD ->ffff810008e00000 on node 0
[ffffe20004e00000-ffffe20004ffffff] PMD ->ffff810009200000 on node 0
[ffffe20005000000-ffffe200051fffff] PMD ->ffff810009600000 on node 0
[ffffe20005200000-ffffe200053fffff] PMD ->ffff810009a00000 on node 0
[ffffe20005400000-ffffe200055fffff] PMD ->ffff810009e00000 on node 0
[ffffe20005600000-ffffe200057fffff] PMD ->ffff81000a200000 on node 0
[ffffe20005800000-ffffe200059fffff] PMD ->ffff81000a600000 on node 0
[ffffe20005a00000-ffffe20005bfffff] PMD ->ffff81000aa00000 on node 0
[ffffe20005c00000-ffffe20005dfffff] PMD ->ffff81000ae00000 on node 0
[ffffe20005e00000-ffffe20005ffffff] PMD ->ffff81000b200000 on node 0
Zone PFN ranges:
 DMA             0 ->     4096
 DMA32        4096 ->  1048576
 Normal    1048576 ->  1769472
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
   0:        0 ->      159
   0:      256 ->   786144
   0:  1048576 ->  1769472
On node 0 totalpages: 1506943
 DMA zone: 56 pages used for memmap
 DMA zone: 1387 pages reserved
 DMA zone: 2556 pages, LIFO batch:0
 DMA32 zone: 14280 pages used for memmap
 DMA32 zone: 767768 pages, LIFO batch:31
 Normal zone: 9856 pages used for memmap
 Normal zone: 711040 pages, LIFO batch:31
 Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10b9a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
PM: Registered nosave memory: 00000000bfee0000 - 00000000bfee3000
PM: Registered nosave memory: 00000000bfee3000 - 00000000bfef0000
PM: Registered nosave memory: 00000000bfef0000 - 00000000bff00000
PM: Registered nosave memory: 00000000bff00000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: bff00000:20100000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 45232 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1481364
Policy zone: Normal
Kernel command line: ro root=UUID=426b48bd-0e69-4ef2-b53f-896642325d92 rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2819.217 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Node 0: aperture @ 5df4000000 size 32 MB
Aperture beyond 4GB. Ignoring.
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ c000000
PM: Registered nosave memory: 000000000c000000 - 0000000010000000
Memory: 5869108k/7077888k available (2657k kernel code, 158664k reserved, 1395k data, 356k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 5641.85 BogoMIPS (lpj=2820925)
Security Framework initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12585800
Detected 12.585 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5638.16 BogoMIPS (lpj=2819082)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon? 64 X2 Dual Core Processor 5600+ stepping 03
Brought up 2 CPUs
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=208 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=224 bytes
sizeof(task_struct)=6272 bytes
CPU0 attaching sched-domain:
domain 0: span 00000000,00000003
 groups: 00000000,00000001 00000000,00000002
 domain 1: span 00000000,00000003
  groups: 00000000,00000003
CPU1 attaching sched-domain:
domain 0: span 00000000,00000003
 groups: 00000000,00000002 00000000,00000001
 domain 1: span 00000000,00000003
  groups: 00000000,00000003
net_namespace: 1016 bytes
Time: 15:43:15  Date: 06/06/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:11.0: set SATA to AHCI mode
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 ? Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
DMAR:parse DMAR table failure.
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ c000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x220-0x225 has been reserved
system 00:01: ioport range 0x290-0x294 has been reserved
system 00:02: ioport range 0x4100-0x411f has been reserved
system 00:02: ioport range 0x228-0x22f has been reserved
system 00:02: ioport range 0x238-0x23f has been reserved
system 00:02: ioport range 0x40b-0x40b has been reserved
system 00:02: ioport range 0x4d6-0x4d6 has been reserved
system 00:02: ioport range 0xc00-0xc01 has been reserved
system 00:02: ioport range 0xc14-0xc14 has been reserved
system 00:02: ioport range 0xc50-0xc52 has been reserved
system 00:02: ioport range 0xc6c-0xc6d has been reserved
system 00:02: ioport range 0xc6f-0xc6f has been reserved
system 00:02: ioport range 0xcd0-0xcd1 has been reserved
system 00:02: ioport range 0xcd2-0xcd3 has been reserved
system 00:02: ioport range 0xcd4-0xcdf has been reserved
system 00:02: ioport range 0x4000-0x40fe has been reserved
system 00:02: ioport range 0x4210-0x4217 has been reserved
system 00:02: ioport range 0xb00-0xb0f has been reserved
system 00:02: ioport range 0xb10-0xb1f has been reserved
system 00:02: ioport range 0xb20-0xb3f has been reserved
system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0c: iomem range 0xcea00-0xcffff has been reserved
system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
system 00:0c: iomem range 0xbfee0000-0xbfefffff could not be reserved
system 00:0c: iomem range 0xffff0000-0xffffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0x100000-0xbfedffff could not be reserved
system 00:0c: iomem range 0xbfff0000-0xcffeffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0c: iomem range 0xfff80000-0xfffeffff has been reserved
PCI: Bridge: 0000:00:01.0
 IO window: e000-efff
 MEM window: 0xfde00000-0xfdffffff
 PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
PCI: Bridge: 0000:00:0a.0
 IO window: d000-dfff
 MEM window: 0xfdd00000-0xfddfffff
 PREFETCH window: 0x00000000fda00000-0x00000000fdafffff
PCI: Bridge: 0000:00:14.4
 IO window: c000-cfff
 MEM window: 0xfdc00000-0xfdcfffff
 PREFETCH window: 0x00000000fdb00000-0x00000000fdbfffff
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0a.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2898k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1212766995.371:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:13.0: OHCI: BIOS handoff failed (BIOS bug?) 00000184
pci 0000:01:05.0: Boot video device
PCI: Setting latency timer of device 0000:00:0a.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0a.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: ACPI0007:01 is registered as cooling_device1
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
 Magic number: 12:723:739
Freeing unused kernel memory: 356k freed
Write protecting the kernel read-only data: 1120k
ACPI: PCI Interrupt 0000:00:12.2[b] -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02c000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:12.2
ACPI: PCI Interrupt 0000:00:13.2[b] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe029000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ehci_hcd
usb usb2: SerialNumber: 0000:00:13.2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe02e000
hub 1-0:1.0: unable to enumerate USB device on port 5
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ohci_hcd
usb usb3: SerialNumber: 0000:00:12.0
ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe02d000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ohci_hcd
usb usb4: SerialNumber: 0000:00:12.1
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02b000
hub 1-0:1.0: unable to enumerate USB device on port 5
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ohci_hcd
usb usb5: SerialNumber: 0000:00:13.0
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02a000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 3 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ohci_hcd
usb usb6: SerialNumber: 0000:00:13.1
ACPI: PCI Interrupt 0000:00:14.5[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe028000
usb 4-2: new low speed USB device using ohci_hcd and address 2
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: OHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.25.3-18.fc9.x86_64 ohci_hcd
usb usb7: SerialNumber: 0000:00:14.5
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
ahci 0000:00:11.0: version 3.0
ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:11.0: controller can't do PMP, turning off CAP_PMP
usb 4-2: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-2/4-2:1.0/input/input2
input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:12.1-2
usb 4-2: New USB device found, idVendor=046d, idProduct=c040
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: USB-PS/2 Optical Mouse
usb 4-2: Manufacturer: Logitech
ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pio slum part 
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: HPA detected: current 488395055, native 488397168
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 1:0:0:0: Direct-Access     ATA      ST3250620AS      3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 488395055 512-byte hardware sectors (250058 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 488395055 512-byte hardware sectors (250058 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 > sda4
sd 1:0:0:0: [sda] Attached SCSI disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:8192 avtab hash slots allocated. Num of rules:167099
SELinux:8192 avtab hash slots allocated. Num of rules:167099
security:  8 users, 12 roles, 2308 types, 113 bools, 1 sens, 1024 cats
security:  72 classes, 167099 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev sda7, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=allow
type=1403 audit(1212767003.558:2): policy loaded auid=4294967295 ses=4294967295
sd 1:0:0:0: Attached scsi generic sg0 type 0
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:00.0 to 64
r8169 0000:02:00.0: no MSI. Back to INTx.
eth0: RTL8168c/8111c at 0xffffc20000c42000, 00:1d:7d:d9:a7:a4, XID 3c2000c0 IRQ 18
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: Power Button (CM) [PWRB]
ACPI: WMI: Mapper loaded
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt for device 0000:00:14.1 disabled
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
input: PC Speaker as /devices/platform/pcspkr/input/input5
ata5.01: ATAPI: TSSTcorpCD/DVDW SH-S182D, SB02, max UDMA/33
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ata5.01: configured for UDMA/33
ata6.00: HPA detected: current 586070255, native 586072368
ata6.00: ATA-7: ST3300620AS, 3.AAE, max UDMA/133
ata6.00: 586070255 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata6.00: simplex DMA is claimed by other device, disabling DMA
ata6.00: configured for PIO4
scsi 4:0:1:0: CD-ROM            TSSTcorp CD/DVDW SH-S182D SB02 PQ: 0 ANSI: 5
scsi 4:0:1:0: Attached scsi generic sg1 type 5
scsi 5:0:0:0: Direct-Access     ATA      ST3300620AS      3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 586070255 512-byte hardware sectors (300068 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sdb] 586070255 512-byte hardware sectors (300068 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 <<6>ppdev: user-space parallel port driver
sdb5 sdb6 >
sd 5:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg2 type 0
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:1:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
ALSA sound/pci/hda/hda_intel.c:1810: chipset global capabilities = 0x4401
ALSA sound/pci/hda/hda_intel.c:749: codec_mask = 0x1
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
ALSA sound/pci/hda/hda_codec.c:2857: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0)
ALSA sound/pci/hda/hda_codec.c:2861:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:2865:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:2866:    mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:2874:    inputs: mic=0x18, fmic=0x19, line=0x1a, fline=0x0, cd=0x0, aux=0x0
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Headphone Playback Volume, skipped
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Speaker Playback Volume, skipped
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Mono Playback Volume, skipped
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Line-Out Playback Volume, skipped
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Speaker Playback Switch, skipped
ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Mono Playback Switch, skipped
ACPI: PCI Interrupt 0000:01:05.1[b] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:01:05.1 to 64
ALSA sound/pci/hda/hda_intel.c:1810: chipset global capabilities = 0x1001
ALSA sound/pci/hda/hda_intel.c:749: codec_mask = 0x1
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [email protected]
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda7, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda8, type ext3), uses xattr
SELinux: initialized (dev sda1, type ext2), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sdb5, type ext3), uses xattr
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sdb6, type ext3), uses xattr
Adding 1951856k swap on /dev/sda6.  Priority:-1 extents:1 across:1951856k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
powernow-k8: Found 1 AMD Athlon? 64 X2 Dual Core Processor 5600+ processors (2 cpu cores) (version 2.20.00)
powernow-k8:    0 : fid 0x14 (2800 MHz), vid 0xa
powernow-k8:    1 : fid 0x12 (2600 MHz), vid 0xc
powernow-k8:    2 : fid 0x10 (2400 MHz), vid 0xe
powernow-k8:    3 : fid 0xe (2200 MHz), vid 0x10
powernow-k8:    4 : fid 0xc (2000 MHz), vid 0x10
powernow-k8:    5 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    6 : fid 0x2 (1000 MHz), vid 0x12
ip6_tables: ? 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: ? 2000-2006 Netfilter Core Team
Clocksource tsc unstable (delta = -85303303 ns)
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
fuse init (API version 7.9)
SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
it87: Found IT8718F chip at 0x228, revision 5
it87: in3 is VCC (+5V)
r8169: eth0: link up
r8169: eth0: link up
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 2 processor cores.
vboxdrv: fAsync=1 u64DiffCores=1128215.
vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 1.6.0 (interface 0x00070001).
SELinux: initialized (dev cifs, type cifs), uses genfs_contexts
SELinux: initialized (dev cifs, type cifs), uses genfs_contexts
eth0: no IPv6 routers present
hda-intel: Invalid position buffer, using LPIB read method instead.
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
VirtualBox[2821] trap int3 ip:30f0447836 sp:41e76dc0 error:0

 

Trochę tu chyba nadmiarowych informacji, ale nic to.

 

Edit

 

Troszkę wyciąłem z tego:

ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: HPA detected: current 488395055, native 488397168
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
EXT3-fs: mounted filesystem with ordered data mode.
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
ata5.01: ATAPI: TSSTcorpCD/DVDW SH-S182D, SB02, max UDMA/33
ata5.01: configured for UDMA/33
ata6.00: HPA detected: current 586070255, native 586072368
ata6.00: ATA-7: ST3300620AS, 3.AAE, max UDMA/133
ata6.00: 586070255 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata6.00: simplex DMA is claimed by other device, disabling DMA
ata6.00: configured for PIO4

 

Problem tkwi zapewne tutaj:

 

ata6.00: simplex DMA is claimed by other device, disabling DMA
ata6.00: configured for PIO4

 

tylko czemu DMA jest już zajęte (to znaczy wiem, sda je zajął ale móg by się podzielić ;] ) i jak to poprawić?

Choć PIO4 powinno mi dać więcej do 16MB/s , mam tylko 1,5MB/s

 

Tutaj jakby wszystko OK, gwiazdka przy udma6 :

 

[root@infinity tmp]# hdparm -i /dev/sd?

/dev/sda:

Model=ST3250620AS                             , FwRev=3.AAC   , SerialNo=            5QF066G2
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=488395055
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes:  pio0 pio1 pio2 pio3 pio4 
DMA modes:  mdma0 mdma1 mdma2 
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
AdvancedPM=no WriteCache=enabled
Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

* signifies the current active mode


/dev/sdb:

Model=ST3300620AS                             , FwRev=3.AAE   , SerialNo=            9QF3GZ45
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=586070255
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes:  pio0 pio1 pio2 pio3 pio4 
DMA modes:  mdma0 mdma1 mdma2 
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
AdvancedPM=no WriteCache=enabled
Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

* signifies the current active mode

 

tu jest chyba rozwiązanie mojego problemu, tylko jak się blacklistuje w fedorze ?

http://ubuntuforums.org/showthread.php?t=760121

[morsik]

Blacklist nic nie da, już to robiłem. Ja sam nie wiem w czym tkwi problem (mój był taki iż napęd CD był na MASTER, a dysk na SLAVE). Spróbuj "na chama" ustawić DMA:

hdparm -d1 /dev/sdb

[xdarkflame]

to SATA hdparm na niego nie działa ...

 

No a jak to blacklist zrobić ? U ciebie nie zadziało bo na jednym kabelku z cd to dysk zawsze zwalnia ( chyba że to cd z szybkim kontroleram ;] )

 

Edit:

dodałem blacklist ata_generic do /etc/modprobe.d/blacklist, niestety nie pomogło a mi się pomysły skończyły

[markus]

Ja walcząc z brakiem DMA przy DVD odkryłem, że za ten komunikat

 

simplex DMA is claimed by other device, disabling DMA

 

jest odpowiedzialny pata_acpi, przynajmniej u mnie tak było, bo po blacklistowaniu tego modułu komunikat zniknął. Niestety mojego problemu to nie rozwiązało, ale może ten rozwiąże.

 

A blacklist zrobiłem tak, że dodałem

blacklist pata_acpi

do /etc/modprobe.conf, następnie wykonałem

mkinitrd -f /boot/initrd-<wersja kernela>.img <wersja kernela>

i restart systemu

 

Pomoże, nie pomoże....spróbowac można

[xdarkflame]

Pomogło w 100%

 

Wielkie dzięki, znów mogę dysku używać.

Miejmy nadzieje, że nic innego nie przestało działać.