JozekW Napisano Styczeń 2, 2009 Zgłoszenie Share Napisano Styczeń 2, 2009 Korzystam z modemu Huawei E220 w sieci PLAY. Działa poprawnie w Fedorze 9 na laptopie (i386), ale mam problem na Fedorze 10 (x86_64). Używam następujących plików konfiguracyjnych: [root@localhost ~]# cat /etc/wvdial.conf [Dialer Defaults] Phone = *99# Username = any Password = any Stupid Mode = 1 SetVolume = 0 Dial Command = ATDT FlowControl = NOFLOW [Dialer hsdpa] Modem = /dev/ttyUSB0 Baud = 460800 #Init1 = AT+CPIN={tutaj PIN karty, UWAGA ! Nie musisz w telefonie wyłączać żądania PIN-u - były takie posty} - UWAGA ! Ta linia musi wystąpić tylko RAZ, jeśli łączenie się nie powiedzie, należy przygotować kolejną sekcję już bez tego pinu !!, albo wyjąć kartę i włożyć ponownie (niepolecane) Init2 = ATZ Init3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ISDN = 0 Modem Type = Analog Modem [Dialer winda] Init5 = AT &FE0 V1 X1 &D2 &C1 S0=0 Dial Attempts = 3 [Dialer 384k] Init6 = AT+CGEQMIN=1,4,64,384,64,384 Init7 = AT+CGEQREQ=1,4,64,384,64,384 [Dialer 144k] Init6 = AT+CGEQMIN=1,4,64,144,64,144 Init7 = AT+CGEQREQ=1,4,64,144,64,144 [Dialer 64k] Init6 = AT+CGEQMIN=1,4,64,64,64,64 Init7 = AT+CGEQREQ=1,4,64,64,64,64 [root@localhost ~]# cat /etc/ppp/peers/wvdial plugin passwordfd.so noauth name wvdial noipdefault nomagic usepeerdns ipcp-accept-local ipcp-accept-remote nomp noccp nopredictor1 Do uruchomienia internetu wydaję polecenie: [root@localhost ~]# wvdial hsdpa winda --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ OK --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Sending: AT &FE0 V1 X1 &D2 &C1 S0=0 AT &FE0 V1 X1 &D2 &C1 S0=0 OK --> Modem initialized. --> Sending: ATDT*99# --> Waiting for carrier. CONNECT 7200000 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Mon Dec 29 08:49:00 2008 --> Pid of pppd: 3385 --> Using interface ppp0 --> local IP address 94.254.212.6 --> remote IP address 10.64.64.64 --> primary DNS address 10.11.12.13 --> secondary DNS address 10.11.12.14 Gdy odpalam to wszystko na laptopie z Fedora 9 i386 to wszystko działa jak trzeba, natomiast na drugim komputerze, gdzie jest Fedora 10 kernel-2.6.27.9-159.fc10.x86_64, lampka modemu świeci światłem ciągłym fioletowym (zalogowany), ale działa tylko ping na 'locat IP'. Pingi na 'remote IP' i inne nie działają. Czy powinienem jeszcze coś skonfigurować? Proszę o pomoc. --------------- Listingi do 12-15 linijek umieszczaj między znacznikami [code] i [/code], dłuższe niż 15 linii pomiędzy [codebox] i [/codebox] - tak jest czytelniej. Przeczytaj "BB Code Help". WalDo Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
qmic Napisano Styczeń 2, 2009 Zgłoszenie Share Napisano Styczeń 2, 2009 Mam pytanie, dlaczego cokolwiek konfigurujesz jak powinnno działać bez żadnej konfiguracji przez Network Managera (Auto GSM Connection). Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
adios Napisano Styczeń 3, 2009 Zgłoszenie Share Napisano Styczeń 3, 2009 Proszę nie dublować tematów i to własnych ! http://forum.fedora.pl/index.php?showtopic=19826 Z noworocznej dobroci nie usunę dubla tematu. Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
qmic Napisano Styczeń 3, 2009 Zgłoszenie Share Napisano Styczeń 3, 2009 Usuń usuń Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
JozekW Napisano Styczeń 4, 2009 Autor Zgłoszenie Share Napisano Styczeń 4, 2009 Mam pytanie, dlaczego cokolwiek konfigurujesz jak powinnno działać bez żadnej konfiguracji przez Network Managera (Auto GSM Connection). Bo nie wiedziałem, że tak można. Dzięki za pomoc. Usunąłem moje pliki konfiguracyjne i użyłem NetworkManager, no i oczywiście zadziałało. Pozdrawiam Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
qmic Napisano Styczeń 4, 2009 Zgłoszenie Share Napisano Styczeń 4, 2009 Bo nie wiedziałem, że tak można. Dzięki za pomoc. Usunąłem moje pliki konfiguracyjne i użyłem NetworkManager, no i oczywiście zadziałało. Pozdrawiam Za to chyba najbardziej lubię Network Managera Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
orrik Napisano Luty 25, 2009 Zgłoszenie Share Napisano Luty 25, 2009 Witam Pozwolicie że się dołączę pod temat. Czy moglibyście mi podpowiedzieć (na podstawie tego logu )czemu nie mogę uzyskać połączenia ? Feb 25 12:35:55 localhost kernel: usb 6-2: new full speed USB device using uhci_hcd and address 2 Feb 25 12:35:55 localhost kernel: usb 6-2: configuration #1 chosen from 1 choice Feb 25 12:35:55 localhost kernel: usb 6-2: New USB device found, idVendor=12d1, idProduct=1003 Feb 25 12:35:55 localhost kernel: usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Feb 25 12:35:55 localhost kernel: usb 6-2: Product: HUAWEI Mobile Feb 25 12:35:55 localhost kernel: usb 6-2: Manufacturer: HUAWEI Technologies Feb 25 12:35:56 localhost kernel: Initializing USB Mass Storage driver... Feb 25 12:35:56 localhost kernel: scsi6 : SCSI emulation for USB Mass Storage devices Feb 25 12:35:56 localhost kernel: usbcore: registered new interface driver usb-storage Feb 25 12:35:56 localhost kernel: USB Mass Storage support registered. Feb 25 12:35:56 localhost kernel: usb 6-2: USB disconnect, address 2 Feb 25 12:35:56 localhost kernel: usb 6-2: new full speed USB device using uhci_hcd and address 3 Feb 25 12:35:56 localhost kernel: usb 6-2: configuration #1 chosen from 1 choice Feb 25 12:35:56 localhost kernel: usb-storage: probe of 6-2:1.0 failed with error -5 Feb 25 12:35:56 localhost kernel: usb-storage: probe of 6-2:1.1 failed with error -5 Feb 25 12:35:56 localhost kernel: scsi9 : SCSI emulation for USB Mass Storage devices Feb 25 12:35:56 localhost kernel: usb 6-2: New USB device found, idVendor=12d1, idProduct=1003 Feb 25 12:35:56 localhost kernel: usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Feb 25 12:35:56 localhost kernel: usb 6-2: Product: HUAWEI Mobile Feb 25 12:35:56 localhost kernel: usb 6-2: Manufacturer: HUAWEI Technologies Feb 25 12:35:57 localhost kernel: usbcore: registered new interface driver usbserial Feb 25 12:35:57 localhost kernel: usbserial: USB Serial support registered for generic Feb 25 12:35:57 localhost kernel: usbcore: registered new interface driver usbserial_generic Feb 25 12:35:57 localhost kernel: usbserial: USB Serial Driver core Feb 25 12:35:57 localhost kernel: usbserial: USB Serial support registered for GSM modem (1-port) Feb 25 12:35:57 localhost kernel: option 6-2:1.0: GSM modem (1-port) converter detected Feb 25 12:35:57 localhost kernel: usb 6-2: GSM modem (1-port) converter now attached to ttyUSB0 Feb 25 12:35:57 localhost kernel: option 6-2:1.1: GSM modem (1-port) converter detected Feb 25 12:35:57 localhost kernel: usb 6-2: GSM modem (1-port) converter now attached to ttyUSB1 Feb 25 12:35:57 localhost kernel: usbcore: registered new interface driver option Feb 25 12:35:57 localhost kernel: option: USB Driver for GSM modems: v0.7.2 Feb 25 12:35:57 localhost NetworkManager: <info> ttyUSB0: driver is 'option'. Feb 25 12:35:57 localhost NetworkManager: <info> Found new Modem device 'ttyUSB0'. Feb 25 12:35:57 localhost NetworkManager: <info> (ttyUSB0): exported as /org/freedesktop/Hal/devices/usb_device_12d1_1003_noserial_if0_serial_usb_0 Feb 25 12:36:01 localhost NetworkManager: <info> (ttyUSB0): device state change: 1 -> 2 Feb 25 12:36:01 localhost NetworkManager: <info> (ttyUSB0): deactivating device (reason: 2). Feb 25 12:36:01 localhost NetworkManager: nm_system_device_flush_ip4_routes_with_iface: assertion `iface_idx >= 0' failed Feb 25 12:36:01 localhost NetworkManager: nm_system_device_flush_ip4_addresses_with_iface: assertion `iface_idx >= 0' failed Feb 25 12:36:01 localhost NetworkManager: <info> (ttyUSB0): device state change: 2 -> 3 Feb 25 12:36:01 localhost kernel: scsi 9:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 Feb 25 12:36:01 localhost kernel: sr1: scsi-1 drive Feb 25 12:36:01 localhost kernel: sr 9:0:0:0: Attached scsi generic sg2 type 5 Feb 25 12:36:53 localhost NetworkManager: <info> Activation (ttyUSB0) starting connection 'Automatyczne poĹ?Ä?czenie komĂłrkowe GSM' Feb 25 12:36:53 localhost NetworkManager: <info> (ttyUSB0): device state change: 3 -> 4 Feb 25 12:36:53 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Feb 25 12:36:53 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Feb 25 12:36:53 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Feb 25 12:36:53 localhost NetworkManager: <info> (ttyUSB0): powering up... Feb 25 12:36:54 localhost NetworkManager: <info> Registered on Home network Feb 25 12:36:54 localhost NetworkManager: <info> Associated with network: +COPS: 0,0,"",2 Feb 25 12:36:54 localhost NetworkManager: <info> Connected, Woo! Feb 25 12:36:54 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 2 of 5 (Device Configure) scheduled... Feb 25 12:36:54 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 2 of 5 (Device Configure) starting... Feb 25 12:36:54 localhost NetworkManager: <info> (ttyUSB0): device state change: 4 -> 5 Feb 25 12:36:54 localhost NetworkManager: <info> Starting pppd connection Feb 25 12:36:54 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 2 of 5 (Device Configure) complete. Feb 25 12:36:54 localhost pppd[2675]: Plugin /usr/lib/pppd/2.4.4/nm-pppd-plugin.so loaded. Feb 25 12:36:54 localhost kernel: PPP generic driver version 2.4.2 Feb 25 12:36:54 localhost kernel: NET: Registered protocol family 10 Feb 25 12:36:54 localhost kernel: lo: Disabled Privacy Extensions Feb 25 12:36:54 localhost kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready Feb 25 12:36:54 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Feb 25 12:36:54 localhost pppd[2675]: pppd 2.4.4 started by root, uid 0 Feb 25 12:36:54 localhost pppd[2675]: Using interface ppp0 Feb 25 12:36:54 localhost pppd[2675]: Connect: ppp0 <--> /dev/ttyUSB0 Feb 25 12:36:54 localhost NetworkManager: <info> (ttyUSB0): device state change: 5 -> 6 Feb 25 12:36:54 localhost pppd[2675]: CHAP authentication succeeded Feb 25 12:36:54 localhost pppd[2675]: CHAP authentication succeeded Feb 25 12:36:54 localhost NetworkManager: <info> (ttyUSB0): device state change: 6 -> 7 Feb 25 12:36:54 localhost kernel: PPP Deflate Compression module registered Feb 25 12:37:01 localhost pppd[2675]: Could not determine remote IP address: defaulting to 10.64.64.64 Feb 25 12:37:01 localhost pppd[2675]: local IP address 89.108.219.112 Feb 25 12:37:01 localhost pppd[2675]: remote IP address 10.64.64.64 Feb 25 12:37:01 localhost pppd[2675]: primary DNS address 10.11.12.13 Feb 25 12:37:01 localhost pppd[2675]: secondary DNS address 10.11.12.14 Feb 25 12:37:01 localhost NetworkManager: <info> PPP manager(IP Config Get) reply received. Feb 25 12:37:01 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) scheduled... Feb 25 12:37:01 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) started... Feb 25 12:37:01 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) scheduled... Feb 25 12:37:01 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) complete. Feb 25 12:37:01 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) started... Feb 25 12:37:03 localhost NetworkManager: <info> (ttyUSB0): device state change: 7 -> 8 Feb 25 12:37:03 localhost NetworkManager: <info> Policy set 'Automatyczne poĹ?Ä?czenie komĂłrkowe GSM' (ppp0) as default for routing and DNS. Feb 25 12:37:03 localhost NetworkManager: <info> Activation (ttyUSB0) successful, device activated. Feb 25 12:37:03 localhost NetworkManager: <info> Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) complete. Feb 25 12:37:32 localhost NetworkManager: <info> (ttyUSB0): device state change: 8 -> 3 Będę niezmiernie wdzięczny za pomoc. Orrik // ============ edit ============ exbros ============ ... dla dlugich listingow stosuj znaczniki [ codebox ] zamiast [ code ] Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
Rekomendowane odpowiedzi
Jeśli chcesz dodać odpowiedź, zaloguj się lub zarejestruj nowe konto
Jedynie zarejestrowani użytkownicy mogą komentować zawartość tej strony.
Zarejestruj nowe konto
Załóż nowe konto. To bardzo proste!
Zarejestruj sięZaloguj się
Posiadasz już konto? Zaloguj się poniżej.
Zaloguj się