Gość Napisano Luty 27, 2015 Zgłoszenie Share Napisano Luty 27, 2015 mam problem z internetem przewodowym. internet cały czas się łączy i łączy i nie uzyskuje połączenia z routerem. karta ethernetowa: 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection (2) I218-V system: Linux tokariew.pl 3.18.7-200.fc21.x86_64 #1 SMP Wed Feb 11 21:53:17 UTC 2015 x86_64 x86_64 x86_64 GNU/Linux próbowałem aktualizacji sterownika e1000e, ale po zainstalowaniu i restarcie cały czas mam starą wersję, a bez restartu mam tak: [ 0.914379] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 0.914381] e1000e: Copyright(c) 1999 - 2014 Intel Corporation. [ 0.914490] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 0.914503] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 1.067754] e1000e 0000:00:19.0 eth0: registered PHC clock [ 1.067766] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) d0:50:99:34:55:32 [ 1.067767] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.067792] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF [ 1.068326] e1000e 0000:00:19.0 enp0s25: renamed from eth0 [ 16.153035] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 16.253051] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 20.564053] e1000e: enp0s25 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [ 20.564064] e1000e 0000:00:19.0 enp0s25: 10/100 speed: disabling TSO [ 265.851384] e1000e 0000:00:19.0 enp0s25: removed PHC [ 265.945365] e1000e: enp0s25 NIC Link is Down [ 310.174296] e1000e: module verification failed: signature and/or required key missing - tainting kernel [ 310.175028] e1000e: Intel(R) PRO/1000 Network Driver - 3.1.0.2-NAPI [ 310.175030] e1000e: Copyright(c) 1999 - 2014 Intel Corporation. [ 310.175186] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 310.175202] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 310.344226] e1000e 0000:00:19.0 eth0: registered PHC clock [ 310.344239] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) d0:50:99:34:55:32 [ 310.344240] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 310.344263] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF [ 310.346678] e1000e 0000:00:19.0 enp0s25: renamed from eth0 [ 310.444213] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 310.545056] e1000e 0000:00:19.0: irq 30 for MSI/MSI-X [ 314.694162] e1000e: enp0s25 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [ 314.694167] e1000e 0000:00:19.0 enp0s25: 10/100 speed: disabling TSO komputer po podłączeniu bezprzewodowej karty pod usb łączy się z siecią bez problemu. w menadżerze połączeń mam ustawienie dhcp przy adresach Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
@sunrise Napisano Luty 27, 2015 Zgłoszenie Share Napisano Luty 27, 2015 Używasz NetworkManagera? Co zwraca polecenie journalctl --unit NetworkManager Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
Gość Napisano Luty 28, 2015 Zgłoszenie Share Napisano Luty 28, 2015 lut 28 01:10:33 tokariew.pl NetworkManager[834]: <info> startup complete lut 28 01:10:33 tokariew.pl NetworkManager[834]: <info> Connectivity check for uri 'https://fedoraproject.org/static/hotspot.txt' failed with 'Błąd podczas rozwiązywania "fedoraproject.org": Ta nazwa lub usługa jest nieznana'. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) starting connection 'Połączenie przewodowe 1' lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 1 of 5 (Device Prepare) scheduled... lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 1 of 5 (Device Prepare) started... lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): device state change: disconnected -> prepare (reason 'none') [30 40 0] lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> NetworkManager state is now CONNECTING lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 2 of 5 (Device Configure) scheduled... lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 1 of 5 (Device Prepare) complete. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 2 of 5 (Device Configure) starting... lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): device state change: prepare -> config (reason 'none') [40 50 0] lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 2 of 5 (Device Configure) successful. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 2 of 5 (Device Configure) complete. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 3 of 5 (IP Configure Start) scheduled. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 3 of 5 (IP Configure Start) started... lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): device state change: config -> ip-config (reason 'none') [50 70 0] lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Beginning DHCPv4 transaction (timeout in 45 seconds) lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> dhclient started with pid 3363 lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Beginning DHCPv6 transaction (timeout in 45 seconds) lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> dhclient started with pid 3364 lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 3 of 5 (IP Configure Start) complete. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): DHCPv4 state changed nbi -> preinit lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): DHCPv6 state changed nbi -> preinit6 lut 28 01:10:46 tokariew.pl dhclient[3364]: Can't bind to dhcp address: Cannot assign requested address lut 28 01:10:46 tokariew.pl dhclient[3364]: Please make sure there is no other dhcp server lut 28 01:10:46 tokariew.pl dhclient[3364]: running and that there's no entry for dhcp or lut 28 01:10:46 tokariew.pl dhclient[3364]: bootp in /etc/inetd.conf. Also make sure you lut 28 01:10:46 tokariew.pl dhclient[3364]: are not running HP JetAdmin software, which lut 28 01:10:46 tokariew.pl dhclient[3364]: includes a bootp server. lut 28 01:10:46 tokariew.pl dhclient[3364]: lut 28 01:10:46 tokariew.pl dhclient[3364]: This version of ISC DHCP is based on the release available lut 28 01:10:46 tokariew.pl dhclient[3364]: on ftp.isc.org. Features have been added and other changes lut 28 01:10:46 tokariew.pl dhclient[3364]: have been made to the base software release in order to make lut 28 01:10:46 tokariew.pl dhclient[3364]: it work better with this distribution. lut 28 01:10:46 tokariew.pl dhclient[3364]: lut 28 01:10:46 tokariew.pl dhclient[3364]: Please report for this software via the Red Hat Bugzilla site: lut 28 01:10:46 tokariew.pl dhclient[3364]: http://bugzilla.redhat.com lut 28 01:10:46 tokariew.pl dhclient[3364]: lut 28 01:10:46 tokariew.pl dhclient[3364]: exiting. lut 28 01:10:46 tokariew.pl NetworkManager[834]: <info> (enp0s25): DHCPv6 client pid 3364 exited with status 1 lut 28 01:10:46 tokariew.pl dhclient[3363]: DHCPDISCOVER on enp0s25 to 255.255.255.255 port 67 interval 3 (xid=0xc1ac770b) lut 28 01:10:46 tokariew.pl dhclient[3363]: DHCPREQUEST on enp0s25 to 255.255.255.255 port 67 (xid=0xc1ac770b) lut 28 01:10:46 tokariew.pl dhclient[3363]: DHCPOFFER from 192.168.1.1 lut 28 01:10:46 tokariew.pl dhclient[3363]: DHCPNAK from 192.168.1.1 (xid=0xc1ac770b) lut 28 01:10:53 tokariew.pl dhclient[3363]: DHCPREQUEST on enp0s25 to 255.255.255.255 port 67 (xid=0xc1ac770b) lut 28 01:10:53 tokariew.pl dhclient[3363]: DHCPNAK from 192.168.1.1 (xid=0xc1ac770b) lut 28 01:11:14 tokariew.pl dhclient[3363]: DHCPDISCOVER on enp0s25 to 255.255.255.255 port 67 interval 4 (xid=0xa2a93027) lut 28 01:11:14 tokariew.pl dhclient[3363]: DHCPREQUEST on enp0s25 to 255.255.255.255 port 67 (xid=0xa2a93027) lut 28 01:11:14 tokariew.pl dhclient[3363]: DHCPOFFER from 192.168.1.1 lut 28 01:11:14 tokariew.pl dhclient[3363]: DHCPNAK from 192.168.1.1 (xid=0xa2a93027) lut 28 01:11:19 tokariew.pl dhclient[3363]: DHCPREQUEST on enp0s25 to 255.255.255.255 port 67 (xid=0xa2a93027) lut 28 01:11:19 tokariew.pl dhclient[3363]: DHCPNAK from 192.168.1.1 (xid=0xa2a93027) lut 28 01:11:32 tokariew.pl NetworkManager[834]: <warn> (enp0s25): DHCPv4 request timed out. lut 28 01:11:32 tokariew.pl NetworkManager[834]: <info> (enp0s25): canceled DHCP transaction, DHCP client pid 3363 lut 28 01:11:32 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 4 of 5 (IPv4 Configure Timeout) scheduled... lut 28 01:11:32 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 4 of 5 (IPv4 Configure Timeout) started... lut 28 01:11:32 tokariew.pl NetworkManager[834]: <info> Activation (enp0s25) Stage 4 of 5 (IPv4 Configure Timeout) complete. lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> WiFi hardware radio set enabled lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> WiFi now enabled by radio killswitch lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6) supports 4 scan SSIDs lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: starting -> ready lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: ready -> disconnected lut 28 01:12:28 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6) supports 4 scan SSIDs lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Auto-activating connection 'tokariew'. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) starting connection 'tokariew' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) scheduled... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) started... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: disconnected -> prepare (reason 'none') [30 40 0] lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) scheduled... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) complete. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) starting... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: prepare -> config (reason 'none') [40 50 0] lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6/wireless): access point 'tokariew' has security, but secrets are required. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: config -> need-auth (reason 'none') [50 60 0] lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) complete. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) scheduled... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: disconnected -> inactive lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) started... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: need-auth -> prepare (reason 'none') [60 40 0] lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) scheduled... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 1 of 5 (Device Prepare) complete. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) starting... lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: prepare -> config (reason 'none') [40 50 0] lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6/wireless): connection 'tokariew' has security, and secrets exist. No new secrets needed. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: added 'ssid' value 'tokariew' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: added 'scan_ssid' value '1' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: added 'key_mgmt' value 'WPA-PSK' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: added 'psk' value '<omitted>' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: added 'proto' value 'WPA RSN' lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 2 of 5 (Device Configure) complete. lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> Config: set interface ap_scan to 1 lut 28 01:12:29 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: inactive -> scanning lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: scanning -> authenticating lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: authenticating -> associated lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): supplicant interface state: associated -> completed lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'tokariew'. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 3 of 5 (IP Configure Start) scheduled. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 3 of 5 (IP Configure Start) started... lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: config -> ip-config (reason 'none') [50 70 0] lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Beginning DHCPv4 transaction (timeout in 45 seconds) lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> dhclient started with pid 3418 lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 3 of 5 (IP Configure Start) complete. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): DHCPv4 state changed nbi -> preinit lut 28 01:12:30 tokariew.pl dhclient[3418]: DHCPREQUEST on wlp0s20u6 to 255.255.255.255 port 67 (xid=0x8f3a9334) lut 28 01:12:30 tokariew.pl dhclient[3418]: DHCPACK from 192.168.1.1 (xid=0x8f3a9334) lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): DHCPv4 state changed preinit -> reboot lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> address 192.168.1.104 lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> plen 24 (255.255.255.0) lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> gateway 192.168.1.1 lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> server identifier 192.168.1.1 lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> lease time 259200 lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> hostname 'dhcppc4' lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> nameserver '8.8.8.8' lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> nameserver '8.8.8.4' lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 5 of 5 (IPv4 Configure Commit) scheduled... lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 5 of 5 (IPv4 Commit) started... lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: ip-config -> ip-check (reason 'none') [70 80 0] lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 5 of 5 (IPv4 Commit) complete. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: ip-check -> secondaries (reason 'none') [80 90 0] lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> (wlp0s20u6): device state change: secondaries -> activated (reason 'none') [90 100 0] lut 28 01:12:30 tokariew.pl dhclient[3418]: bound to 192.168.1.104 -- renewal in 105341 seconds. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Policy set 'tokariew' (wlp0s20u6) as default for IPv4 routing and DNS. lut 28 01:12:30 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) successful, device activated. lut 28 01:13:02 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... lut 28 01:13:02 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 4 of 5 (IPv6 Configure Timeout) started... lut 28 01:13:02 tokariew.pl NetworkManager[834]: <info> Activation (wlp0s20u6) Stage 4 of 5 (IPv6 Configure Timeout) complete. Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
@WalDo Napisano Luty 28, 2015 Zgłoszenie Share Napisano Luty 28, 2015 Ale chodzi ci w końcu o przewodowy czy bezprzewodowy? Może wystarczy kliknąć w ikonę NM, rozłączyć WiFi i włączyć ethernet? Przy podawaniu logów też lepiej wyłączyć WiFi, bo tylko zaciemnia obraz. Wg mnie nowy sterownik albo źle zainstalowany albo sobie nie radzi z tą kartą. Wróć do starego jeśli działał. Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
@sunrise Napisano Luty 28, 2015 Zgłoszenie Share Napisano Luty 28, 2015 Ale chodzi ci w końcu o przewodowy czy bezprzewodowy? Może wystarczy kliknąć w ikonę NM, rozłączyć WiFi i włączyć ethernet? Przy podawaniu logów też lepiej wyłączyć WiFi, bo tylko zaciemnia obraz. Wg mnie nowy sterownik albo źle zainstalowany albo sobie nie radzi z tą kartą. Wróć do starego jeśli działał. Autorowi chodzi o połączenie przewodowe, spójrz na pierwszy post, sterownik jest jest w kernelu (nie wiem co auto miał na myśli mówiąc "próbowałem aktualizacji sterownika e1000e") i działa prawidłowo, mam taką samą kartę, działającą na tym samym sterowniku. Do autora wątku, problemem są te komunikaty lut 28 01:10:46 tokariew.pl dhclient[3364]: Can't bind to dhcp address: Cannot assign requested address lut 28 01:10:46 tokariew.pl dhclient[3364]: Please make sure there is no other dhcp server lut 28 01:10:46 tokariew.pl dhclient[3364]: running and that there's no entry for dhcp or lut 28 01:10:46 tokariew.pl dhclient[3364]: bootp in /etc/inetd.conf. Also make sure you lut 28 01:10:46 tokariew.pl dhclient[3364]: are not running HP JetAdmin software, which lut 28 01:10:46 tokariew.pl dhclient[3364]: includes a bootp server. co zwraca polecenie ifconfig, spróbuj usunąć z NetworkManagera interface enp0s25 i dodać go ponownie. Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
Gość Napisano Luty 28, 2015 Zgłoszenie Share Napisano Luty 28, 2015 (edytowane) ifconfig: enp0s25: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::d250:99ff:fe34:5532 prefixlen 64 scopeid 0x20<link> ether d0:50:99:34:55:32 txqueuelen 1000 (Ethernet) RX packets 44 bytes 7872 (7.6 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 14 bytes 3614 (3.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xf7d00000-f7d20000 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 0 (Local Loopback) RX packets 424 bytes 35784 (34.9 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 424 bytes 35784 (34.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255 ether 8a:f6:12:a9:7f:6b txqueuelen 0 (Ethernet) RX packets 0 bytes 0 (0.0 RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 co do aktualizacji, z strony intela pobrałem najnowszą wersję, zbudowałem bez problemu paczkę rpm i ją zainstalowałem w systemie, ale nadal jest używana ta bazowa. jak usunąć intrface z networkmenagera? ok po konfiguracji ręcznej połączenia przewodowego poszło, ale czemu przez dhcp nie działa to nie wiem. Edytowane Luty 28, 2015 przez tokariew Odnośnik do komentarza Udostępnij na innych stronach More sharing options...
Rekomendowane odpowiedzi
Jeśli chcesz dodać odpowiedź, zaloguj się lub zarejestruj nowe konto
Jedynie zarejestrowani użytkownicy mogą komentować zawartość tej strony.
Zarejestruj nowe konto
Załóż nowe konto. To bardzo proste!
Zarejestruj sięZaloguj się
Posiadasz już konto? Zaloguj się poniżej.
Zaloguj się